When Using Power Tools Never Engage The Quizlet?

When using power tools, it is crucial to disconnect the power source and avoid engaging the trigger lock. This is especially important when replacing parts such as bits, blades, or discs. To disconnect the power source, recharge the tool’s battery, polish it with fine steel wool, and check the tools.

An example of a hydraulic tool is a porta-power, which can weigh 70 to 120 pounds. Before connecting any power tool to a power source, ensure the switch is secure. When using a power drill, proper ground fault protection is essential to prevent damage.

Another important safety measure is the use of a circular saw with an upper blade guard, as it protects you from touching the blade. A locking spring, booster, bit shank, and trigger lock are all essential components to consider when using power tools.

In summary, when using power tools, it is essential to disconnect the power source, recharge the tool’s battery, polish it with fine steel wool, and check the tools. Always engage the trigger lock and disconnect the power source when replacing parts such as bits, blades, or discs.

When operating a power tool, it is important to always _____________.?

Always read and follow the manufacturers instructions before using a power tool. Wear appropriate personal protective equipment, such as safety goggles, ear protection, hard hat, gloves, dust mask and steel-toed shoes. Keep the work area clean and free of clutter to prevent tripping or falling.

What are the four 4 rules for the use of hand power tools?

Hand ToolsAll hand tools, whether furnished by the department or employee owned, must be maintained in safe condition.Hand tools must be inspected before each use. … Hand tools must be used for the designed purpose.Impact tools must be free of mushroomed heads.

Hand and power tools are a common part of our everyday lives and are present in nearly every industry. These tools help us to easily perform tasks that otherwise would be difficult or impossible. However, these simple tools can be hazardous and have the potential for causing severe injuries when used or maintained improperly. Special attention toward hand and power tool safety is necessary in order to reduce or eliminate these hazards.

• Air Tools. Pneumatic power tools must be secured to the hose in such a way as to prevent accidental disconnection. Safety clips or retainers must be securely installed to prevent attachments from being inadvertently expelled.
• Never exceed the manufacturer’s safe operating pressure for all fittings.
• Hoses exceeding ½ inch inside diameter must have a safety device at the source of supply or branch line to reduce pressure in the event of hose failure.

• Hand Tools. All hand tools, whether furnished by the department or employee owned, must be maintained in safe condition.
• Hand tools must be inspected before each use. Unsafe hand tools must not be used on any campus worksite.
• Hand tools must be used for the designed purpose.
• Impact tools must be free of mushroomed heads.
• Wooden handles must be free of cracks or splinters and be tight to the tool.
• Wrenches must not be used when jaws are sprung to the point that slippage occurs.
• Electric power operated tools must be double-insulated or properly grounded.
• Appropriate personal protective equipment, such as safety glasses with side shields, face shields, leather work gloves, or leather work boots must be worn when using hand tools.

When working with power tools, you should always have and wear _________.?

• Here are some key points.. Carefully inspect power tools, cords and accessories before each use.
• Always wear personal protective equipment, including shielded safety glasses or goggles.
• Be sure your power tools are double insulated or grounded.

• Electrical shock
• fires or explosions
• severe cuts, puncture wounds, or injuries from flying debris

What are the five rules you should follow when using power tools?

6 Rules of Power Tool SafetyMake Sure Power Tools Are in Working Order. Before plugging them in and getting to work, take the time to inspect your power tools. … Wear the Right Gear. … Work in a Safe Area. … Handle Your Power Tool Properly. … Be Very Mindful of the People Around You. … Unplug Your Power Tool When its Not in Use.

From nail guns to jackhammers, power tools can play a big part in a day laborers job. To make sure you’re using them safely, follow these six safety rules.

Make Sure Power Tools Are in Working Order. Before plugging them in and getting to work, take the time to inspect your power tools. If you see that it’s dirty and needs to be cleaned or attachments like bits and blades are ready to be changed, this is the time do so. You should also check for any signs of damage to the cord, parts and any safety guards. Doing so decreases your chances of getting hurt due to an equipment malfunction.

Wear the Right Gear. As with any type of day laborer, wearing the right protective clothing and gear is important to staying safe while using power tools. Eyewear like goggles, glasses and shields can keep flying particles from damaging your eyes while working. The proper gloves can protect fingers and help you get a good grip on the tools. Safety shoes with a reinforced toe and non-skid soles can protect you from falling tools and slipping. If the tool you’re working with is especially loud (think jackhammers), ear plugs is another piece of PPE you should wear at all times.

What are 3 safety rules that must be followed with every power tool?

Make sure cutters or blades are clean, sharp and securely in place. Never use bent, broken, or warped blades or cutters. Never overreach when using a power tool. Stay firmly planted on both feet.

When using electric power tools what should be done before using the tool?

• Wear or use personal protective equipment (PPE) or clothing that is appropriate for the work you are doing
• this may include items such as safety glasses or goggles, or a face shield (with safety glasses or goggles), hearing protection, dust mask, gloves, safety boots or shoes, or rubber boots.
• Switch off the tools before connecting them to a power supply.
• If a power cord feels more than comfortably warm or if a tool is sparking, have it checked by an electrician or other qualified person.
• Disconnect the power supply before making adjustments or changing accessories.
• Remove any wrenches and adjusting tools before turning on a tool.
• Inspect the cord for fraying or damage before each use. Tag defective tools clearly with an Out of service tag and replace immediately with a tool in good running order.
• During use, keep power cords clear of tools and the path that the tool will take.
• Use clamps, a vice or other devices to hold and support the piece being worked on, when practical to do so. This will allow you to use both hands for better control of the tool and will help prevent injuries if a tool jams or binds in a work piece.
• Use only approved extension cords that have the proper wire size (gauge) for the length of cord and power requirements of the electric tool that you are using. This will prevent the cord from overheating.
• For outdoor work, use outdoor extension cords marked W-A or W.
• Suspend power cords over aisles or work areas to eliminate stumbling or tripping hazards.
• Eliminate octopus connections: if more than one receptacle plug is needed, use a power bar or power distribution strip that has an integral power cord and a built-in overcurrent protection.
• Pull the plug, not the cord when unplugging a tool. Pulling the cord causes wear and may adversely affect the wiring to the plug and cause electrical shock to the operator.
• Follow good housekeeping procedures – keep the work area free of clutter and debris that could be tripping or slipping hazards.
• Keep power cords away from heat, water, oil, sharp edges and moving parts. They can damage the insulation and cause a shock.
• Ensure that cutting tools, drill bits, etc. are kept sharp, clean and well maintained.
• Store tools in a dry, secure location when they are not being used.

• Do not wear gloves, loose clothing or jewelry while using revolving power tools. Tie back long hair or wear appropriate hair protection to prevent hair from getting caught in moving parts of equipment.
• Do not use a tool unless you have been trained to use it safely and know its limitations and hazards.
• Avoid accidental starting by ensuring the tool is turned off before you plug it in. Also do not walk around with a plugged-in tool with your finger touching the switch.
• Do not bypass the ON/OFF switch and operate the tools by connecting and disconnecting the power cord.
• Do not disconnect the power supply of the tool by pulling or jerking the cord from the outlet.
• Do not leave a running tool unattended. Do not leave it until it has been turned off, has stopped running completely, and has been unplugged.
• Do not use electric tools in wet conditions or damp locations unless tool is connected to a ground fault circuit interrupter (GFCI).
• Do not expose electric power tools to rain or wet conditions
• wet tools increase the likelihood of electric shock.
• Avoid body contact with grounded surfaces like refrigerators, pipes and radiators when using electric powered tools
• this will reduce the likelihood of shock if the operators body is grounded.
• Do not plug several power cords into one outlet by using single-to-multiple outlet adapters or converters (cube taps).
• Do not use light duty power cords.
• Stop using an electric power tool if you feel a tingle in your fingers. This is a warning that the tool is faulty and needs repair.
• Do not connect or splice extension cords together to make a longer connection: the resulting extension cord may not be able to provide sufficient current or power safely.
• Do not carry electrical tools by the power cord.
• Do not tie power cords in knots. Knots can cause short circuits and shocks. Loop the cords or use a twist lock plug.

• Never break off the third prong on a plug: replace broken 3-prong plugs and make sure the third prong is properly grounded.
• Never use extension cords as permanent wiring: use extension cords only as a temporary power supply to an area that does not have a power outlet.
• Do not walk on or allow vehicles or other moving equipment to pass over unprotected power cords. Cords should be put in conduits or protected by placing planks on each side of them.
• Do not brush away sawdust, shavings or turnings while the tool is running. Never use compressed air for cleaning surfaces or removing sawdust, metal turnings, etc.
• Do not operate tools in an area containing explosive vapours or gases.
• Do not clean tools with flammable or toxic solvents.
• Do not surprise or touch anyone who is operating a tool. Startling a tool operator could end up causing an accident or injury.

When using power tools, be sure the switch is in the?

OFF Be sure the power tools switch is OFF before plugging it in or inserting a battery pack. Do not carry tools with your finger on the switch.

When operating a power tool, it is important to always quizlet.?

– Always wear eye protection when operating power tools. – tie back long hair and remove all jewelry. – Keep your work area clean.

When using power tools, never engage the _____.?

When using power tools, never engage the trigger lock.